|
Model
|
KV-03
|
||
|
Oil Consumption
|
2-4L/H
|
||
|
Output Power
|
14-50KW
|
||
|
Max.Output Heat
|
30,000Kcal/H (120,000Btu/H)
|
||
|
brass siphon 1x1.0mm
|
|||
|
Tube Diameter
|
90mm
|
||
|
Tube Length
|
130mm
|
||
|
Heating Pipe
|
1.0KW
|
||
|
Motor Power
|
180W
|
||
|
Power Supply
|
220V 50HZ or 110V 60HZ
|
||
|
Burner Size(LxWxH)
|
430x450x290mm
|
||
|
N.W
|
20kg
|
||
|
working pressure
|
0.5bar(7psi)
ps:must work with external air compressor.
smallest capacity(120L/min) is good to use
|
||
|
Fuel
|
all kinds of waste oil,waste mixed oil,diesel oil
|
||
|
Application
|
0.1T boiler,furnace,oven,air heater,grain dryer,
distiller etc
|
each Kv03 burner packed in double carton box,package size is
580x530x420mm.G.W is 30kg
package list:one Kv03 burner,one set oil pump&filter system,extra spare
parts,simple kit tool,catalogue&manual etc
detailed manual,video
spare parts for life time
online support
1.misfunction and solution:
mal button lights,quick flicker turns to slowly flicker.
Press reset button to see if burner is back to work.If not,take off the photo cell and wipe.
Mal button is alway light,reset button can't press.
In this case,power off and connect the power again.
It is a normal misfunction,because new burner,there is no oil in oil pump and filter.Pump can’t supply oil within 2 mins,oil float gives message to print board,to shut down the burner for protection.
Heat button is lighting,then light the mal button.
There is too much water in the oil.
use the valve in the bottom of the small tank to leak water.
Stilling oil for a night,let me water and oil seperate.
Ignition rod is striking fire,but no fire.
Use the tool to remove the nozzle,check if it has been blocked,change the rubber pad too.
The tool and rubber pads are also with the burner,we send you for this situation.
If you meet other problem,contact us first .
2.Have you improved and innovated your product?
As a factory,we improve and innovate all the time,we take customers requirment seriously.For example:
We insulate copper in demand of NZ customer need.
We change the print board's programme to reach 30s purge.some countries have demand for that.
We change the manual air flap to automatic system.To low down the noise.
We use one air compressor for two or three air solenoid system,to reduce the cost for customer.
If you have any requirement for burner,please let me know.
3.Customers have their own oil system,no need of oil pump system.Is that ok?
Yes,it's ok.Please let me know first.To see if we have to change the print board accordingly.
4.Do customers need to prepare the pre-filer?
No.We have it with the burner.If you have your own ideas,then it's ok.
5.Comparing waste oil burner within air pump,some diesel modified burner and other waste oil burner brand,what's the difference?
We are true waste oil system,differ from waste oil burner within compressor,diesel modifed burner or other brand.
6.Is necessary the burner working with 1 unit outside compressor?
Yes.It is.Because the simple principle is high pressure atomizing.
7.what's the air compressor would match your burner&heater?
waste oil heater and small waste oil burner use the smallest air compressor(120L/min) or above
KV-40,KV-50,KV-60 use 880-900L/min air compressor or above
KV-90,KV-120 use 1250L/min air compressor or above
ps:Air compressor is better bigger than small.Bigger one can supply enough compressed air once,while small capacity compressor may work continually.
8.I am not so familiar about waste oil burner,which type should I choose?
It's ok.Contact us,we will guide you the best burner.
Yes,it’s ok.Just let us know.
Kingwei Energy are direct factory for waste oil burner&heater for more
than 15 years,international sales team set up in the year of 2014.Band is
KING VITAL.Our factory mainly includes two workshop and two section, machine tool workshop,burner&heater asseble workshop,burner&heater
test section,package section. Since international sales team set up,We are honored to have several
solid clients stood by us all way along.Happy to see several customers
trust us and started a dealership.We also supply burner&heater to end
user directly.We learn from all clients&customers above.It is a amazing
journey that we may never meet but benefit from each other directly. Factory and office is now merged together.All order will be arranged
more efficiently.All advice will be executed immediately. Boiler workshop was set up in the year of 2018.We are ready to provide
one stop service to utilize your waste oil!
machine tool workshop
burner&heater asseble workshop
