| Model | KV-30 |
| Oil Consumption | 15-21L/H |
| Output Power | 210-270kw |
| Max.Output Heat | 300,000Kcal/H(12,00,000Btu/H) |
| Nozzle | siphon brass 3x2.0mm |
| Tube Diameter | 114mm |
| Tube Length | 135mm |
| Heating Pipe | 1.0kw |
| Motor Power | 180w |
| Power Supply | 220v 50hz Or 110v 60hz |
| Burner Size(LxWxH) | 510x455x300mm |
| N.W | 25kg |
| Working Pressure |
0.5bar (7psi) ps:must work with external air compressor smallest capacity is 120l/min |
| Fuel | all kinds of waste oil,waste mixed oil,diesel oil |
| Application |
0.5T boiler,furnace,air heater,grain dryer, distiller etc |
each Kv05 Kv10 Kv20 Kv30 burner packed in double carton box,package
size is 580x530x420mm.G.W is 30kg
package list:one burner,one set oil pump&filter system,extra spare
parts,simple kit tool,catalogue&manual etc
detailed manual,video
spare parts for life time
online support
machine tool workshop
burner&heater assemble workshop
boiler workshop
1.misfunction and solution:
mal button lights,quick flicker turns to slowly flicker.
Press reset button to see if burner is back to work.If not,take off the photo cell and wipe.
Mal button is alway light,reset button can't press.
In this case,power off and connect the power again.
It is a normal misfunction,because new burner,there is no oil in oil pump and filter.Pump can’t supply oil within 2 mins,oil float gives message to print board,to shut down the burner for protection.
Heat button is lighting,then light the mal button.
There is too much water in the oil.
use the valve in the bottom of the small tank to leak water.
Stilling oil for a night,let me water and oil seperate.
Ignition rod is striking fire,but no fire.
Use the tool to remove the nozzle,check if it has been blocked,change the rubber pad too.
The tool and rubber pads are also with the burner,we send you for this situation.
If you meet other problem,contact us first .
2.Have you improved and innovated your product?
As a factory,we improve and innovate all the time,we take customers requirment seriously.For example:
We insulate copper in demand of NZ customer need.
We change the print board's programme to reach 30s purge.some countries have demand for that.
We change the manual air flap to automatic system.To low down the noise.
We use one air compressor for two or three air solenoid system,to reduce the cost for customer.
If you have any requirement for burner,please let me know.
3.Customers have their own oil system,no need of oil pump system.Is that ok?
Yes,it's ok.Please let me know first.To see if we have to change the print board accordingly.
4.Do customers need to prepare the pre-filer?
No.We have it with the burner.If you have your own ideas,then it's ok.
5.Comparing waste oil burner within air pump,some diesel modified burner and other waste oil burner brand,what's the difference?
We are true waste oil system,differ from waste oil burner within compressor,diesel modifed burner or other brand.
6.Is necessary the burner working with 1 unit outside compressor?
Yes.It is.Because the simple principle is high pressure atomizing.
7.what's the air compressor would match your burner&heater?
KV-03,KV-05,KV-10,KV-20,KV-30 matches around 0.3-0.5cbm/min(5-9L/s) ac
KV-50,KV-60 matches around 0.7-1cbm/min(11-17L/s) ac
KV-90,KV-120 matches around 1.2-1.5cbm/min(20-25L/s) ac
KVH-1000,KVH-2000,KVH-5000 and KVH-6000 matches around 0.3-0.5cbm/min(5-9L/s) ac
Unit conversion:1cmb/min=16.7L/s
8.I am not so familiar about waste oil burner,which type should I choose?
It's ok.Contact us,we will guide you the best burner.
Yes,it’s ok.Just let us know.
