|
Model
|
KV40
|
||
|
Oil Consumption
|
30-40L/H
|
||
|
Output Power
|
230-360kw
|
||
|
Max.output heat
|
400,000Kcal/h (16,00,000Btu/h)
|
||
|
siphon brass 4x2.0mm
|
|||
|
Tube Diameter
|
160mm
|
||
|
Tube Length
|
188mm
|
||
|
Heating Pipe
|
1.1kw
|
||
|
Motor Power
|
750w
|
||
|
Power Supply
|
220v 50hz Or 110v 60hz
|
||
|
Burner Size(LxWxH)
|
640x550x660mm
|
||
|
N.W
|
34kg
|
||
|
Working Pressure
|
0.5-1 bar(7-10PSI)
ps:must work with external air compressor
smallest capacity is 880L/min
|
||
|
Fuel
|
all kinds of waste oil,waste mixed oil,diesel oil
|
||
|
Application
|
0.6T boiler,furnace,oven,grain dryer etc
|
each Kv40,Kv50,Kv60 burner packed in plywood box,inside
foam,cardboard,film for protection. package size is 820x625x620mm.G.W is 60kg
package list:one burner,one set oil pump&filter system,extra spare
parts,simple kit tool,catalogue&manual etc
detailed manual,video
spare parts for life time
online support
machine tool workshop
burner&heater assemble workshop
boiler workshop
1.misfunction and solution:
●mal button lights,quick flicker turns to slowly flicker.
Press reset button to see if burner is back to work.If not,take off the photo cell and wipe.
●Mal button is alway light,reset button can't press.
In this case,power off and connect the power again.
It is a normal misfunction,because new burner,there is no oil in oil pump and filter.Pump can't supply oil within 2 mins,oil float gives message to print board,to shut down the burner for protection.
●Heat button is lighting,then light the mal button.
There is too much water in the oil.
use the valve in the bottom of the small tank to leak water.
Stilling oil for a night,let me water and oil seperate.
●Ignition rod is striking fire,but no fire.
Use the tool to remove the nozzle,check if it has been blocked,change the rubber pad too.
The tool and rubber pads are also with the burner,we send you for this situation.
If you meet other problem,contact us first .
2.Have you improved and innovated your product?
As a factory,we improve and innovate all the time,we take customers requirment seriously.For example:
We insulate copper in demand of NZ customer need.
We change the print board's programme to reach 30s purge.some countries have demand for that.
We change the manual air flap to automatic system.To low down the noise.
We use one air compressor for two or three air solenoid system,to reduce the cost for customer.
If you have any requirement for burner,please let me know.
3.Customers have their own oil system,no need of oil pump system.Is that ok?
Yes,it's ok.Please let me know first.To see if we have to change the print board accordingly.
4.Do customers need to prepare the pre-filer?
No.We have it with the burner.If you have your own ideas,then it's ok.
5.Comparing waste oil burner within air pump,some diesel modified burner and other waste oil
burner brand,what's the difference?
We are true waste oil system,differ from waste oil burner within compressor,diesel modifed burner or other brand.
For example,we design the photo cells specifically for waste oil burner,more sensitive and precision than photodiodes.
6.Is necessary the burner working with 1 unit outside compressor?
Yes.It is.Because the simple principle is high pressure atomizing.
7.what's the air compressor would match your burner&heater?
KV-03,KV-05,KV-10,KV-20,KV-30 and waste oil heater use the smallest air compressor(120L/min) or above
KV-40,KV-50,KV-60 use 880-900L/min air compressor or above
KV-90,KV-120 use 1250L/min air compressor or above
ps:Air compressor is better bigger than small.Bigger one can supply enough compressed air once,while small capacity compressor may work continually.
8.I am not so familiar about waste oil burner,which type should I choose?
It's ok.Contact us,we will guide you the best burner.
9.Can I pay by credit card instead of going to bank?
Yes,it's ok.Just let us know.
