HC-JP70 is a high-displacement mortar spraying machine with modern technology. It has the functions of pumping, bonding and spraying. The conveying rate is high, the pumping distance is long, and it is easy to pump large granular materials, which can be used for spraying pre-mixed mortar and mixing mortar on site. Set screw pump anti-wear control structure: It has the function of separating the screw pump shaft and the casing directly on the machine: Adjusting the displacement and remote control function, and integrating the pressure sensing. Suitable for all kinds of plastering mortar, thermal insulation mortar, bonding mortar, fiber mortar, facing mortar, interface mortar, floor mortar, fireproof mortar, refractory mortar, self-leveling mortar, masonry mortar, reinforced mortar, filled mortar, perfusion Mortar transport and spraying.

wall plaster machine HC-JS311 type

wall plaster machine HC-JS511 type

product details

Wear-resistant high pressure pipe
Made of rubber and steel wire, it is wear-resistant, explosion-proof and corrosion-resistant. 7 meters working radius, distance is not a problem

Precision pressure gauge
Accurate measurement, reasonable design, stainless steel, imported quality, good performance

6 gun nozzles
Easy to change and disassemble, multiple choices, wearable and durable

Solid tire
Strong load-bearing, high-strength rubber
Strong and durable, long service life

Large flow pump head
Large capacity pump head, imported quality, stable performance

Strong air pump
long lasting
Can achieve a good spray effect

Mortar spraying machine instructions
1. Adapt to spraying materials: water-soluble materials such as putty powder, paint, cement mortar, mortar, thermal insulation material, waterproof material, fireproof material, heat insulation material, sound absorbing material.
2. The connection between the spray gun and the feeding tube can be rotated, the yin and yang angles, and the top plate can be freely sprayed for easy operation.
3. High construction efficiency and good quality
4. Small size, easy to carry on site, and low cost of accessories.
5. Easy to use (no need to take scaffolding, no mobile equipment, no need to repair the equipment), fast, save materials, save money, 150m2 / h.
6. Material ratio (cement) 0.7-1:3 mortar.
This machine is a point screw type high pressure mortar spraying machine with advanced technology, simple operation and maintenance, and can be operated skillfully without special training. The main disadvantages of the artificial powder wall and the previously introduced powder wall machine are the low degree of adhesion between the mortar and the wall and the density of the mortar. The flow rate of this machine is high and the pressure is high, which overcomes the above defects. The density of the mortar far exceeds the national regulations. Standards to avoid problems caused by problems such as quality, construction period and wages.
It is multi-purpose, can spray mortar, waterproof coating, refractory material, and is not affected by regional and environmental conditions and spray surface.

Quick operation introduction
1. Turn on the power, press the button, the screw pump and start working. If the steering is reversed, press the stop button to stop. Adjust the power and change the steering. If it is in the opposite direction, it will not be discharged.
2. Inject a small amount of water into the inlet of the delivery hose, or use a screw pump to pump the water to wet the delivery hose, and then gradually drain the tube water from the outlet. The drainage should be clean and no residual water should remain in the pipe.
3. Put the evenly mixed material into the hopper, press the start button, the shotcrete work will start, and in the work, combined with the adjustment of the air volume, but the spray quality is the best.
4. The mixing material must be added continuously in the hopper to ensure the continuity of the spraying work.
5. Before the end of the spraying work, stop the machine after the remaining material in the hopper is sprayed. Remove the gun and remove the parts and gradually clean them.
6. Inject 50kg of clean water into the hopper and start the pump to clean the water. After the nozzle has a clear flow of water, remove the transfer hose and roll it up.
7. Maintenance and maintenance
8. After each cleaning, a little silicone oil must be added to lubricate and prevent rust. The purpose is to protect the core from rust and start smoothly after the next use. When the machine is working, the electric box door must be closed and locked to prevent dust and moisture from invading. When cleaning the machine, the electric box part can only be wiped, not flushed, and the gearbox oil is often checked.

Construction Site

Newest Products

We will update new products, if had any interested, just notice this part.

Packaging & Shipping

1. Testing Machine before package

2. Package : Inside plastic bag, outside wooden case. 

3. Shipping: By sea, By air.

    By sea: if customer not urgently the machine, we advice by sea, even though by sea took time is long, but by sea reduce much money about the freight, and it is good for customer if the machine is heavy and big size.

    By air: it is faster than by sea, but its freight is higher much than by sea, so this kind of type always suggest for light, small size and urgently demand machine.

Pre-sale service
1.Related machines’s technical parameter will be supplied to customer.
2.According to customer’s factory size, factory layout can be provided in advance.

3. According to customer’s material cost, general formulation can be prepared well.
4.Special machine can be supplied as customer’s request.
5.Professional Advice about Market, machines, processing , materials, packing can be supplied
 6. Suggesting professional ship agent or helping book ship as customer request. 

 After sale service:

1.Allocation chart as the buyer’s request will be supplied. 
2.Operation manual will be supplied after shipment.
3.One year warrantee, life time maintenance with cost price.
4.Free easy broken spare parts will be sent with container .
5.First installation can be done by engineer.
6.Training workers in customer’s factory.

If you had any problem, just feel free to contact with us.

Any time, we will reply you as soon as possible!