Industrial Brush
Civilian Brush
Brush Equipment
Brush Raw Materials
Decoration Materials
∨
∧
NINGBO SPRING SMILES TADA TRADE CO., LTD.
Business units
ChinaVIP0Audited Supplier
Response Time: within 24 hours
Response Rate: 100%
+ Follow
View Shop
Chat Now
Add to wish list
+ Add a New List
Solar Charger Ultrasonic Animal Extruder Infrared Sensing Drive Cat Cat Dog Light Light Small Animal
OverviewQuick DetailsPest Type:dog repeller,cat repellerPest Control Type:repellerPlace of Origin:Guangdong, China (Mainland)Model Number:51
$8 /
Product Details
Transaction Comments
Solar Charger Ultrasonic Animal Extruder Infrared Sensing Drive Cat Cat Dog Light Light Small Animal Drive Dog Cat repeller
Features :
Driving range: dog, cat
A. Right in front of 110 ° fan-shaped area, 8 to 10 meters range (the details :see product manuals).
B. Solar panels: 4.8V, 4 section 300 mAh, 2/3AA rechargeable batteries.
C. PIR Sensor :Induction the nearby animals.
D.Light sensor :Indicate the working state.
Principle:
1. Through the solar energy function, energy conservation and environmental protection.
2. Do not damage the wildlife, to protect the environment.
3. Find out this kind of animal fearing or hating the audio frequency and made ultrasonic or send light, herding animals from its scope.
About Products:
1, the product uses infrared pyroelectric sensor, the sensor for the degree of sensitivity and movement of the relationship between the animals, the radial movement is not sensitive, and for the cross-movement is the most sensitive. Means that if the animal is still or is straight to the product close to, do not do cross-moving, then the infrared sensor can not, the product is unable to work on animals.
2, it uses the principle of infrared detection, in the detection of small animals at the same time to issue ultrasound to drive small animals. It can help you stay away from nasty stray dogs, stray dogs and other small animals harassment, thus protecting your property, your garden and your garden.
Because it is a portable design product that can be installed in your home, garden, or anywhere in the courtyard, this product can be used with low battery power, the product is only to drive the animal without any chemicals, it is only issued 25kHz Ultrasound to drive them away. Will not have any harm to the human body
1) Speakers: This product can be issued at high frequencies to drive away the animals.
2) PIR motion detector: This is a non-stop output of the infrared sensor, when the sensor to move in the detection range, it will automatically send out the sound frequency of the animal and the LED indicator lights also followed.
3) When the infrared sensor to the animal has been away, the LED indicator will automatically turn off.
4) products with automatic frequency conversion function and light flash function, burst interval 3-5 seconds cycle once, apply to more animals to drive. When the animal is near, the LED lights up automatically and automatically sounds for a few seconds.
5) The product uses a digital sensor head, the sensor is more sensitive, drive better.
1. Unpack the unit completely and confirm that all parts are present.
2. Connect the repeller head, pole sections, connecting part and ground stake.
3. Turn power switch to “ON” position.
4. The PIR repeller is designed to be left ON continuously. It uses four “AA” size NiCD rechargeable batteries.
5. Once turned ON, the LED light and ultrasonic signal will activate for 15 seconds. Following this activation, the unit will move to stand-by
mode.
6. The unit is now ready for installation. The location should allow adequate sunlight to keep the batteries fully charged. Be sure that the area needing protection is within the effective range of the repeller.
7. For best results, keep the repeller head roughly 9-10 inches above ground.
8. Take care not to stress or break the repeller when installing in hard ground. It is a good idea to prepare the ground for the ground stake to avoid damage to the unit.
9. When the PIR sensor detects motion, the LED light will flash for 3 seconds and the ultrasonic signal will run for 15 seconds. Following this, the repeller will return to stand-by mode.
Specifications:
1. Unit Dimensions: 5-1/2” W x 3-1/2” D x 14-1/3” H.
2. Unit Weight: 8-1/2 ounces.
3. Power Supply: 4 x “AA” NiCD rechargeable batteries.
4. Power Consumption: Standby = 0.8 mAh, working = 15 mAh
5. Ultrasonic Frequency: 18,000-23,000 Hz
6. Coverage Area: 30 feet @ 110° = 2,425 square feet
CAUTION:
(1)Allow the Animal Repeller to operate continuously for best results.
(2)Do not immerse repeller in water.
(3) Do not cover-up the PIR sensor.
(4)To clean the repeller, use a damp-soft cloth and mild soap with water. Do not use harsh chemicals or abrasive cleaning agents that may damage the repeller.
1. Unpack the unit completely and confirm that all parts are present.
2. Connect the repeller head, pole sections, connecting part and ground stake.
3. Turn power switch to “ON” position.
4. The PIR repeller is designed to be left ON continuously. It uses four “AA” size NiCD rechargeable batteries.
5. Once turned ON, the LED light and ultrasonic signal will activate for 15 seconds. Following this activation, the unit will move to stand-by
mode.
6. The unit is now ready for installation. The location should allow adequate sunlight to keep the batteries fully charged. Be sure that the area needing protection is within the effective range of the repeller.
7. For best results, keep the repeller head roughly 9-10 inches above ground.
8. Take care not to stress or break the repeller when installing in hard ground. It is a good idea to prepare the ground for the ground stake to avoid damage to the unit.
9. When the PIR sensor detects motion, the LED light will flash for 3 seconds and the ultrasonic signal will run for 15 seconds. Following this, the repeller will return to stand-by mode.
Specifications:
1. Unit Dimensions: 5-1/2” W x 3-1/2” D x 14-1/3” H.
2. Unit Weight: 8-1/2 ounces.
3. Power Supply: 4 x “AA” NiCD rechargeable batteries.
4. Power Consumption: Standby = 0.8 mAh, working = 15 mAh
5. Ultrasonic Frequency: 18,000-23,000 Hz
6. Coverage Area: 30 feet @ 110° = 2,425 square feet
CAUTION:
(1)Allow the Animal Repeller to operate continuously for best results.
(2)Do not immerse repeller in water.
(3)Do not cover-up the PIR sensor.
(4)To clean the repeller, use a damp-soft cloth and mild soap with water. Do not use harsh chemicals or abrasive cleaning agents that may damage the repeller.
Other products from this supplier
Back to top
