Led RGB DMX512 Decoder Connect The DMX Digital Console To Change The Light,3Channel 12A 12V 24V DC,288W,CE,EMC,LVD,RoHS,Warranty

 Technical Parameters 

 Led RGB DMX512 Decoder

• Working temperature -20-60℃
• Supply voltage DC12V~24V
• 0utput 3 channels
• Connecting mode common anode
• External dimension L164*W65*H40 mm
• Packing size L183*W82*H60 mm
• Net weight 350g
• Gross weight 390g
• Output gray RGB each 256 levels
• Output current <4A(each channel)
• Output power 12V:<144W, 24V:<288W

 DMX input/output interface:

Adopt Karon standard XLR-3 socket

  Network interface: 

Adopt Standard network line interface.

 Address code and set feature service interface:

 Adopt 10-bit side of the dial-type DIP switch.

Power and Payload interface:

 Adopt male and female connector with screw.

 Direction for use 

 Led RGB DMX512 Decoder

This product is in compliance with DMX512 protocol, and compatible autoindex addressing and manual establishment address.

 Each universal DMX controller takes up 3 DMX addresses. It adopts 2 ways (autoindex addressing and code switch) to set up the address. When adopting the autoindex addressing, all switches are “off” status. When adopting the code switch to set up address, the 10th bit(FUN) is “off” status, and other 9 bits are  binary value code switch which are used to set up the DMX starting address code. The first bit is the lowest order bit, and the ninth is the highest order bit. That can set up 511 address codes. The DMX starting address code is equal to the sum of 1st to 9th bit. If move down one bit of code switch (“ON” set “1”), you can get the placevalue of this bit. If move up (set “0”), the placevalue is 0. For example: if you want to set up DMX starting address code for 73, you should move down the 7th, 4th, and 1st bit of code switch for “1”, and others for “0”, Then the placevalue’s sum of 1st to 9th bit is 64+8+1. That is to say, the DMX512 starting address code is 73. (The correspondence dials code position is as follows)

To choose the channel from the Dial in-line Package(DIP) Switch:

1. Example 1:

   Like figure 1, to set up the DMX starting address code for 37, should move down the 6th, 3th, 1st bit for “1”, others for “0”. Then the placevalue’s sum of 1st to 9th bit is 32+4+1, as is for 37.

                                    Figure 1

2. Example 2:

 Like figure 2, to set up the DMX starting address code for 328, should move down the 9th, 7th, 4th bit for “1”, others for “0”. Then the placevalue’s sum of 1st to 9th bit is 256+64+8, as is for 328.

                                           Figure 2

Other function’s direction for use

1. Test function:

 Signal detection way: When FUN(10)=OFF, and receiving the main control console DMX512 signal, the green signal light on the outer covering would twinkle fast. At the moment, the state of luminaire is controlled by the console. When FUN(10)=ON, the green signal light’s speed would slow down. This time, the state of luminaire is controlled by the addressable switch. When “FUN”=”ON”, the test function like figure 3:

1-9 switch OFF: black

Switch 1=ON: red

Switch 2=ON: green

Switch 3=ON: blue

Switch 4=ON: yellow

Switch 5=ON: purple

Switch 6=ON: cyan

Switch 7=ON: white                                                                                                                                           Figure 3

Switch 8=ON: Seven-color jumpy changing (8 grades of speeds are available)

Switch 9=ON: All-color gradual changing (8 grades of speeds are available)

2. Speed choice of jumpy changing and gradual changing’s effect:

In test function, when switch 8=ON, is for seven-color jumpy changing effect. When switch 9=ON, is for seven-color gradual changing effect. 8 grades of speeds are available for each effect:

1-7 switch OFF: 0 grades of speeds

Switch 1=ON: 1 grade of speeds

Switch 2=ON: 2 grades of speeds

Switch 3=ON: 3 grades of speeds

Switch 4=ON: 4 grades of speeds

Switch 5=ON: 5 grades of speeds

Switch 6=ON: 6 grades of speeds

Switch 7=ON: 7 grades of speeds (maximum speed)

                                                              Figure  4

Like figure 4, when all switches are “ON” at the same time, the more value is taken as final. The state of decoder is Flowing of test function. Its variable speed is 5. In addition, when signal indicator (green) blinks slowly, it runs the built-in program effectiveness of decoder.When the decoder receives the DMX signal,signal indicator will flash rapidly.

Tyical Applications 

Led RGB DMX512 Decoder

Application Circuit1-Serial connection:

Application Circuit2- Serial connection:

Application Circuit3- Serial connection: