Product description:
HB-ZYP-1000 type automatic powder tablet press is a new type of automatic powder tablet press machine. It is a new generation of the new generation of our company based on the existing manual electric tablet press machine. Widely used in the field of powder forming, it can be used to analyze the new materials such as X fluorescence, calcium and iron, superconductivity, building materials, powder ceramics, cement and other new materials. With appropriate accessories, mold can meet the requirements of the customer in the powder molding. This machine has the characteristics of high automation, simple operation, high pressure, high pressure, simple structure, convenient maintenance and so on. It is the replacement product of the existing manual electric tablet press machine, which can meet the need of production.
The machine adopts the latest oil circuit design. The design pressure of the total tonnage of 100 tons, with small size, high pressure, adjustable parameters and other functions, boost, rapid pressure, the formation of moderate operating space, performance stability. According to customer's special technical requirements, the special plane design, manufacture.

Technical parameters:
Pressure range: 3-100T
AC: 380V
Work rate: 1.1kw
Cylinder diameter: 250mm
Piston diameter: 180mm
Working schedule: 50mm
Working space: 260*280mm (long x high)
Dimensions: 300mm x 406mm x 1050mm+
500mm x 420mm x 800mm
Weight: about 380KG

Working principle
This machine is composed of hydraulic and electrical automation system. Through the high pressure infusion pump system, provide the hydraulic power, through the combination of various valve adjustment, to achieve pressure conversion, relying on mechanical and electrical control, to achieve the whole movement process, the work principle of see.

Operation method
1. Starting
The machine uses 380V AC power supply, power consumption 1.1kw. After the power is switched on, press the control button on the panel, switch button indicator light (red) to brighten, then carries on the standby operation. The molding powder stirring evenly and symmetrically into the mold, mold into a work central station and the screw rotation to the appropriate location, press the up button (green), rapidly rising piston can be pressing molding object, and then press the down button (yellow), piston automatic reset, unscrew the screw, remove the workpiece forming, compression midway need emergency stop immediately press the stop button (red), adjustment of the workpiece to be after the re operation of the corresponding button.
2. Pressure adjustment
The maximum pressure of the machine is 100T (20.5MPa). Pressure setting valve for the right side of the black knob below the right, without the need to adjust the user's normal circumstances. If you have to adjust the pressure, take out the special wrench which is used for the pressure adjustment.
, clockwise rotation to increase the pressure, the counterclockwise direction of rotation to reduce pressure, adjust the pressure of each rotation angle as small as possible (such as 15 degrees) do not adjust the pressure change is too large, adjust the boot operation shows the value of pressure. If you have not reached the use requirements, you can repeat the above steps until you reach the ideal state, the pressure adjustment range should be controlled between 3-100T.
3. Pressure conversion table

Note
1. This machine is a high tonnage press, the work space of the goods must be uniform, symmetrical, otherwise the work force is not all, easy to risk, and affect the machine service life.
2. Power protection. This machine uses 380V voltage, the machine must have good grounding protection, to ensure personal safety. The motor rotation direction is clockwise
3. Work always pay attention to the temperature, when the oil temperature of more than 60 degrees, discontinue use and until the machine cooling, the continued use of, the intermittent work must turn off the switch button, in order to reduce the oil temperature.
4. Pay attention to the cleanliness of hydraulic oil, every half year to replace hydraulic oil once, open the oil tank bottom of the oil valve (in the right side of the machine) the hydraulic oil, shut the valve, the oil into the oil, the right side of the machine to add new hydraulic oil, hydraulic oil level to the liquid level meter 2/3.
5. Pressure adjustment, the amount of each adjustment should be as small as possible, and gradually meet the requirements, must pay attention, not to exceed the design tonnage.