45 angle glass machinery  glass deep-processing equipment and the amount generated in the first one of the largest machinery and equipment. The main role of the polished glass, and the production of special shapes. Correct and reasonable use of milling machine, not only to ensure normal production, but also play a role to extend machine life. Divided arm contour milling machine, straight-line edging machine, cam milling machine.

45 angle glass machinery is mainly suitable for furniture glass and architectural glass processing and process glass, glass deep-processing machinery and equipment generated in the first and one of the largest amount of cold working equipment. Mainly used for general flat glass bottom and chamfer grinding and polishing. General manual, digital control, PLC computer control and other configurations. Reasonable operation, daily cleaning lubrication and maintenance, to ensure the normal operation of machinery, mechanical life, improve processing throughput.

Here are what matters milling machine should pay attention to proper use.

1, for a variety of new milling machine purchased before use must first read the manual. After the find out of the machine transmission principle, a variety of handles, hand wheels, electrical button, water, gas regulation valve, master machine maintenance knowledge, before the machine operation.

2, grinding edger grinding quality has a greater impact on the quality of the glass, when grinding position, moving factory space, etc. have been fine, except when using the forward and backward grinding, the rest of the general not to move , so as not to affect the grinding quality. In addition, the grinding back position is not easy to be too large, otherwise easy to damage the waterproof cover, causing leakage, and easy to burn out the motor.

3, the cooling is sufficient also have a greater impact on the grinding effect. Always check the cooling circuit clogging phenomenon. Especially straight line edger bristles easily clogged, and can not easily be detected after plugging will cause insufficient cooling impact milling quality.

4, CVT milling machine used, when adjusting the speed must be in an open state status, otherwise easy to damage CVT edger.

5 Note contour machine when used:

1) sucker shaped machine table are consistent level of greater impact grinding effect. Manufacturers are sucker for five groups were assembled over time from wear, and pick up a uniform thickness so that each sucker sucker glue highly consistent, so that under normal circumstances do not go disassembly sucker. If there is damage to the rubber suction cup, will have to choose to replace the same thickness.

2) shaped machine pumps in use for some time, due to water and other reasons there will be vacuum reduction (ie decrease suction) phenomenon, so pay attention to check and troubleshooting, otherwise the machine work under inadequate suction conditions, on the one hand will affect the mill cut quality, on the other hand also prone to accidents.

6 Note straight line edging machine when used: straight line edging machine (straight edge machine, edging machine, beveling machine) works are clamped around the platen glass and promote its linear motion by grinding. Use must pay attention to two things:

1) front plate and rail junction surface to be lubricated regularly, otherwise they will face in the front and rear guide plate and premature wear and affect the normal life of the machine. Although some models automatic lubricating device, but also regularly check the lubrication line is smooth; 

2)clamping clamping force size glass should be appropriate, too loose influence grinding quality, too tight will make the machine load increases, prone Jitter creeping phenomenon, wear thin glass Shihai easy to clip broken glass. Clamping force of a slightly larger size of the available glass folder on the machine tested, namely: the glass caught in the middle of the machine, stop state his hands moving glass plate, the clamping force transferred feel just could not move his hands when appropriate.

Some photos of glass machinery  for your reference:

1. Do you have any warranty?

Yes, We have. Two years warranty on host machine is given. Six month free replacement warranty for spare parts. We will supply spare parts and sevice during the whole life of the machines.

2. How is your after-sale service?

We have a professional technology supporting team for your timely sevices.

Our engineer has more than 20 years experiences. Please contact us once the machine has any problem. Best sevice will be offered.

3. What certification do you have?

All of our plastering machines have the CE certification which ensure the quality and safety.

Our machine are under strict quality management to ensure good quality.

4. Will you teach how to use the glass machinery ?

Yes, we can provide a complete user manual and usage video for instruction and application.

We have agent.

5. How about the shipment?

THe machine will be shipped within 2-3 days.

6. Can visit your factory?

Welcome to our factory. We would like to make invitation letter for you. Hope we can cooperate with you for a long term.

Our company was founded in 1990. Specialized in manchinery manufacturing for many years. The glass machinery  is our advantages machines. Exported to all over the world such as Asia, Africa, South America, Australia and so on.

Our Principle: Credibility Supremacy, and Customer First

Our Promise: High quality Products, and Excellent Service

Our Value: Being honesty, Doing the best and Long-lasting Development

Our Aim: Develop to be a leader in our industry in the world

If have any interesting in our glass machinery , pls feel free to contact me.

24 hours online.

Ms Kitty Liu / Sale Manager

Skype:

Service Hotline: +86

Whatsapp / wechat :

QQ: 694679222